CA Slr-105 Conversion question

Discuss battery powered AEGs (Automatic Electric Guns) in this forum.
Post a reply

CA Slr-105 Conversion question

Postby Odin's Hammer » Sat Apr 16, 2011 10:42 pm

i have an older ca slr-105 laying around that has been through hell and back but served me well, im building a pmc loadout and would like to bring new life to this gun, ive found a source picture for what id like to attempt and would like to know if its possible and where i should start.

Image

im pretty well deadset on getting something as similar to this as possible, if it means i need to buy a new gun so be it, but if possible id like to go with the current model i have now.

note: guess i should specify i could care less about the attachments and what not im interested in the rail system and barrel, as well as the front gun sight, ill be keeping a full stock rather than folding as well.
Odin's Hammer
Grunt
Grunt
 
Team: N/A
Posts: 11
Age: 41
Joined: Fri Apr 15, 2011 3:23 pm
Top

Postby vibora » Sat Apr 16, 2011 10:51 pm

Somebody's doing a fairly similar build on Arnie's. If nothing else, use it as a baseline. :)

http://www.airsoftretreat.com/forums/in ... ic=97130.0
"Where are you going?"
"I am leaving.....you are about to explode." -Teal'c
User avatar
vibora
Soldier
Soldier
 
Team: N/A
Posts: 155
Age: 32
Images: 7
Joined: Mon Jun 29, 2009 8:29 am
Location: Prescott, AZ
Top

Postby quigly » Sun Apr 17, 2011 12:44 am

To me it looks like a railed piston tube, and a lower RIS with a short barrel. Someone can correct me if I am wrong.
My father once told me, "Some times all you have is a bullet and a prayer, don't miss."
User avatar
quigly
Specops
Specops
 
Team: N/A
Posts: 1230
Age: 31
Joined: Sat May 23, 2009 7:35 pm
Location: Lacey, wa
Top

Postby Cap n pickles » Sun Apr 17, 2011 10:23 am

I have a brand new AK quad rail for sale if you are interested in it for you're project.
Image
"All our liberties are due to men who, when their conscience has compelled them, have broken the laws of the land."
William Kingdon Clifford
User avatar
Cap n pickles
1337
1337
 
Team: N/A
Posts: 3757
Age: 35
Joined: Tue Sep 02, 2008 8:25 pm
Location: The dalles, OR
Top

Postby Odin's Hammer » Sun Apr 17, 2011 11:12 am

Cap n pickles wrote:I have a brand new AK quad rail for sale if you are interested in it for you're project.


pm sent
Odin's Hammer
Grunt
Grunt
 
Team: N/A
Posts: 11
Age: 41
Joined: Fri Apr 15, 2011 3:23 pm
Top

Postby league 4 » Sun Apr 17, 2011 11:54 am

I don't know if you can do the stock, but I'm pretty sure the RIS would be fine.
User avatar
league 4
Specops
Specops
 
Team: 9/G
Posts: 1980
Age: 32
Images: 1
Joined: Sun Aug 05, 2007 7:27 pm
Location: Fort Knox
Top

Postby Odin's Hammer » Sun Apr 17, 2011 12:04 pm

league 4 wrote:I don't know if you can do the stock, but I'm pretty sure the RIS would be fine.


starting to think im gonna have to use a real steel ris
Odin's Hammer
Grunt
Grunt
 
Team: N/A
Posts: 11
Age: 41
Joined: Fri Apr 15, 2011 3:23 pm
Top

Postby league 4 » Sun Apr 17, 2011 12:16 pm

Why? CA AK's are TM compatible, not VFC/dboys compatible so I'd think you would need an airsoft RIS.
User avatar
league 4
Specops
Specops
 
Team: 9/G
Posts: 1980
Age: 32
Images: 1
Joined: Sun Aug 05, 2007 7:27 pm
Location: Fort Knox
Top

Postby Cap n pickles » Sun Apr 17, 2011 12:25 pm

league 4 wrote:Why? CA AK's are TM compatible, not VFC/dboys compatible so I'd think you would need an airsoft RIS.


Some RIS rails for the AK are barrel clamped and not held in by the handguard rings.

So all you need to do is take the hand guards off, put the top rail back on and clamp it.
Image
"All our liberties are due to men who, when their conscience has compelled them, have broken the laws of the land."
William Kingdon Clifford
User avatar
Cap n pickles
1337
1337
 
Team: N/A
Posts: 3757
Age: 35
Joined: Tue Sep 02, 2008 8:25 pm
Location: The dalles, OR
Top

Postby quigly » Sun Apr 17, 2011 1:14 pm

If you do some good shopping around you can get one for not a to outrageous amount.
My father once told me, "Some times all you have is a bullet and a prayer, don't miss."
User avatar
quigly
Specops
Specops
 
Team: N/A
Posts: 1230
Age: 31
Joined: Sat May 23, 2009 7:35 pm
Location: Lacey, wa
Top

Postby quigly » Sun Apr 17, 2011 2:33 pm

Here are a few that might work.

http://shop.ehobbyasia.com/accessories/ ... mount.html

http://shop.ehobbyasia.com/accessories/ ... ystem.html

http://shop.ehobbyasia.com/accessories/ ... orend.html
My father once told me, "Some times all you have is a bullet and a prayer, don't miss."
User avatar
quigly
Specops
Specops
 
Team: N/A
Posts: 1230
Age: 31
Joined: Sat May 23, 2009 7:35 pm
Location: Lacey, wa
Top

Postby Odin's Hammer » Sun Apr 17, 2011 3:06 pm



thank you so very much link one and three are exactly what im looking for
Odin's Hammer
Grunt
Grunt
 
Team: N/A
Posts: 11
Age: 41
Joined: Fri Apr 15, 2011 3:23 pm
Top

Postby Odin's Hammer » Sun Apr 17, 2011 3:15 pm

went ahead and ordered both link 1 and 3 on your list quigly, and went ahead and picked up this instead of using my CA http://www.airsoftgi.com/product_info.p ... ts_id=2652

thank you all for your suggestions and help
Odin's Hammer
Grunt
Grunt
 
Team: N/A
Posts: 11
Age: 41
Joined: Fri Apr 15, 2011 3:23 pm
Top

Postby Android » Sun Apr 17, 2011 4:18 pm

Odin's Hammer wrote:went ahead and ordered both link 1 and 3 on your list quigly, and went ahead and picked up this instead of using my CA http://www.airsoftgi.com/product_info.p ... ts_id=2652

thank you all for your suggestions and help

Be warned: I have that gun & the receiver's made of a cheap magnesium alloy. The rear receiver stock tab broke when I took it apart to re-attach wiring that got loose before I had a chance to even try out the gun. :banghead:
"It's nothing to worry about. It's just a fire on my head."
User avatar
Android
Specops
Specops
 
Team: N/A
Posts: 1570
Age: 47
Images: 13
Joined: Tue May 19, 2009 6:06 am
Location: Portland, OR
Top
Post a reply

Return to AEG/Electrics

Who is online

Users browsing this forum: Bing [Bot] and 3 guests